There are many ways to make your CDMA modem work in Linux. I use these steps to make my CDMA Hisense mobile working with Yemen Mobile network. Using this configuration:
The user and password: ymobile
Dial number: #777
baud: 115200
- Login as root.
- Be sure you have installed these softwares: smpppd, udev, wvdial, and kinternet.
- Do this command: dmesg at the end of the result you will see something like this (not important)
[ 2879.028201] sd 5:0:0:0: [sdb] Assuming drive cache: write through[ 2879.028218] sd 5:0:0:0: [sdb] Attached SCSI removable disk[ 3327.318366] usb 1-1: USB disconnect, address 2[ 3701.313639] input: Virtual pam_fp Keyboard as /devices/virtual/input/input14
- Connect your (USB) mobile, then execute the command dmesg again. Note the change it may look similar to this:
[ 3701.313639] input: Virtual pam_fp Keyboard as /devices/virtual/input/input14[ 4339.456859] usb 3-1: new full speed USB device using uhci_hcd and address 2[ 4339.664308] usb 3-1: New USB device found, idVendor=109b, idProduct=3197[ 4339.664327] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3[ 4339.664340] usb 3-1: Product: COMMON,USB[ 4339.664349] usb 3-1: Manufacturer: COMMON,USB[ 4339.664358] usb 3-1: SerialNumber: Serial Number[ 4339.664540] usb 3-1: configuration #1 chosen from 1 choice
-
Using the results (idVendor=109b, idProduct=3197), write this commandmodprobe -v usbserial vendor=0x109b product=0x3197
- Run the dmesg again. You should see ttyUSB like this.
[ 4339.664540] usb 3-1: configuration #1 chosen from 1 choice[ 4787.132839] usbcore: registered new interface driver usbserial[ 4787.133124] USB Serial support registered for generic[ 4787.133517] usbserial_generic 3-1:1.0: generic converter detected[ 4787.135810] usb 3-1: generic converter now attached to ttyUSB0[ 4787.135848] usbserial_generic 3-1:1.1: generic converter detected[ 4787.136128] usb 3-1: generic converter now attached to ttyUSB1[ 4787.136772] usbcore: registered new interface driver usbserial_generic[ 4787.136783] usbserial: USB Serial Driver corev
-
That means: your modem has installed successfully and you can use it. The device installed at /dev/ttyUSB0
-
check the wvdial configuration by the command cat /etc/wvdial.conf. If the result not like the one below, configure it manually, or by using ether kinternet or wvdialconf.[Dialer Defaults]Init1 = ATZInit2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0Modem = /dev/ttyUSB0Phone = 0Idle Seconds = 300Password = ymobileModem Type = Analog ModemStupid Mode = 1Compuserve = 0Baud = 115200Auto DNS = 1Dial Command = ATDTAsk Password = 0ISDN = 0Username = ymobile
When your configuration is ready, use kinternet to connect to the network. If the connection do not start check the smpppd service.
- Start smpppd service like this:
run yast , insert the root password > system > system services (runlevel) > expert modethen choose the run level 2,3, and 5then start the service, the OK
معلاوي:
ردحذفبصراحه موضوع في قمه الروعه .. لكن للأسف قليل من يهمتمو ويعرفوا قيمه الموضوع هذا بالذات ...
احب اعبر عن شكري لأهتمامك ومحاوله لجعل الشباب ان يثقفوا انفسهم شويه ويطوروا من ذاتهم ...
اخوك معلاوي
ردحذفWe loan at reasonable rates 3% P.A. Personal Loan or Consolidation, Car, Investment, house loan, mortgage loan, etc is given to employees working in Private Limited Company, Public Limited Company, Government Sector, We have special scheme to Credit Card Holder, Insurance Policy Holders Documents Required:- Photograph, Residence Proof address or office address of Existing Company, contact us today and put a stop to your financial problem.Contact Us now:
greenlightcapitalcorporation@gmail.com
Application Form:
=================
Full Name:................
Loan Amount Needed:.
Purpose of loan:.......
Loan Duration:..
Gender:.............
Marital status:....
Location:..........
Home Address:..
City:............
Country:......
Phone:..........
Mobile / Cell:....
Occupation:......
Monthly Income:....
Email Us:(greenlightcapitalcorporation@gmail.com)